View GL602USB_2173280.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

GL602USB GL602USB-a usb keyboard microcontroller specification 1.6 feb. 28, 2001 genesys logic, inc. 10f, no.11, ln.3, tsao ti wei, shenkeng, taipei, taiwan tel: +886-2-2664-6655 fax: +886-2-2664-5757 http://www.genesyslogic.com/ your imagination, our creatio n
revision 1.6 -2- 02/28/2000 index 1 features............................................................................................................4 2 functional overview...............................................................................5 3 pin definitions and descriptions ......................................................6 3.1 GL602USB ....................................................................................................................... ........6 3.2 GL602USB-a..................................................................................................................... ......7 4 functional description .........................................................................9 4.1 memory organization .................................................................................................9 4.2 usb function registers .............................................................................................11 4.3 mcu function registers............................................................................................16 4.4 general purpose i/o ports .......................................................................................18 4.5 timer interrupt.............................................................................................................18 4.6 usb engine..................................................................................................................... ....19 4.7 instruction set summary ........................................................................................21 5 firmware programming guide..........................................................................23 5.1 usb power on reset and bus reset initialization.................................................................23 5.2 suspend/resume/wakeup ......................................................................................................24 5.3 receive packet via endpoint 0 ...............................................................................................25 5.4 transmit packet via endpoint 0..............................................................................................26 5.5 transmit packet via endpoint 1/2/3........................................................................................27 5.6 timer interrupt ................................................................................................................ .......28 5.7 conditional branch............................................................................................................. ....28 5.8 change register bank ........................................................................................................... .28 5.9 change code bank ............................................................................................................... ..28 5.10 receive data from ps/2 mouse port ......................................................................................29 5.11 scan key matrix ................................................................................................................ .....30 5.12 turn led on/off ................................................................................................................ ...30 6 absolute maximum ratings................................................................31 7 electrical characteristics.............................................................31 8 package diagrams ....................................................................................33 8.1 40-pin p-dip................................................................................................................... ........33 8.2 24-pin sop ..................................................................................................................... ........34
revision 1.6 -3- 02/28/2000 figures figure 3-1 40-pin dip (GL602USB) ........................................................................... 7 figure 3-2 24-pin sop (GL602USB-a) ...................................................................... 8 figure 4-1 program memory space............................................................................. 9 figure 4-2 data memory space ................................................................................. 10 figure 4-3 differential input sensitivity over entire common mode range ........... 20 figure 4-4 receiver jitter tolerance.......................................................................... 20 figure 4-5 data signal rise and fall time................................................................ 21 figure 7-3 package outline dimension for 40-pin p-dip........................................... 33 figure 7-4 package outline dimension for 24-pin sop ............................................. 35 tables table 3-1 GL602USB pin definitions and descriptions............................................. 6 table 3-2 GL602USB-a pin definitions and descriptions......................................... 7 table 4-1 usb function register summary ............................................................. 11 table 4-2 mcu function register summary ............................................................ 16
revision 1.6 -4- 02/28/2000 1. features ? low-cost solution for low-speed usb keyboard ? 8-bit micro-controller ? operation speed: 6mhz clock input ? performance: 3 mips @ 6mhz ? single cycle instruction execution ? risc-like architecture ? usb optimized instruction set ? usb specification compliance ? conforms to usb 12mbps specification, version 1.1 ? conforms to usb hid class specification, version 1.1 ? supports 1 device address and 4 endpoints (include endpoint 0) ? i/o ports ? up to 7(GL602USB)/5(GL602USB-a) general purpose i/o pins (otp type is less a gpio pin than mask type). ? up to 8 sense pins and 1 i/o pin with remote wakeup capability ? up to 18(GL602USB)/8(GL602USB-a) output pins optimized for key matrix drive pin ? up to 8(GL602USB)/4(GL602USB-a) output pins optimized for key matrix sense pin ? up to 3(GL602USB)/1(GL602USB-a) i/o pins with led drive capability ? internal memory ? 96 bytes of ram ? 4k x 14 of program rom ? on-chip 3.3v output ? no external regulator required ? improved output drivers with slew-rate control to reduce emi ? 6 mhz external clock ? internal power-on reset (por) ? internal power-fail detector ? supports suspend/normal mode power management ? suspend current lower than 400 a for the whole keyboard system (mask type) ? 8-bit free-running timer ? available in cost saving 40-pin(GL602USB) pdip, 24-pin(GL602USB-a) sop ? support a ps/2 mouse to usb mouse converter in the default firmware.
revision 1.6 -5- 02/28/2000 2. functional overview the GL602USB is an 8-bit risc-like high performance microcontroller with a built-in 1.5mbps sie and transceiver. the microcontroller features 33 instructions optimized for usb keyboard. there are 96 bytes on- chip ram and 4k x 14 bits program rom incorporated into the micro-controller. the micro-controller features 18 output pins and 8 input pins to make a 18 x 8 key matrix. additionally, 3 gpio pins are strong enough to drive leds. 4 gpio pins can be used by any function, for example, support a ps/2 3d mouse to usb 3d mouse converter in the default firmware. legacy usb cable can be used for keyboard in usb mode. all gpio ports feature low emi emissions as a result of improved output drivers with slew-rate control.
revision 1.6 -6- 02/28/2000 3. pin definitions and descriptions 3.1 GL602USB table 3-1 GL602USB pin definitions and descriptions pin no. name i/o description 1 gnd - ground 2 v3.3 o 3.3v output 3 d+ i/o usb data+ 4 d- i/o usb data- 5 drv1 o key matrix output drive 1, open drain output 6 drv2 o key matrix output drive 2, open drain output 7 p1.1/mouse clk i/o port 1 bit 1 / ps2 mouse clock input 8 p1.2/mouse data i/o port 1 bit 2 / ps2 mouse data input 9 p1.3/vpp i/o port 1 bit 3 (for mask) / 12.75v programming power (for otp) 10 p1.4/pwrctl i/o port 1 bit 4 / ps2 mouse power control 11 drv3 o key matrix output drive 3, open drain output 12 drv4 o key matrix output drive 4, open drain output 13 drv5 o key matrix output drive 5, open drain output 14 drv6 o key matrix output drive 6, open drain output 15 drv7 o key matrix output drive 7, open drain output 16 drv8 o key matrix output drive 8, open drain output 17 drv9 o key matrix output drive 9, open drain output 18 drv10 o key matrix output drive 10, open drain output 19 drv11 o key matrix output drive 11, open drain output 20 drv12 o key matrix output drive 12, open drain output 21 drv13 o key matrix output drive 13, open drain output 22 drv14 o key matrix output drive 14, open drain output 23 drv15 o key matrix output drive 15, open drain output 24 drv16 o key matrix output drive 16, open drain output 25 drv17 o key matrix output drive 17, open drain output 26 drv18 o key matrix output drive 18, open drain output 27 sense1 i key matrix input sense 1, internal pull up 10k 28 sense2 i key matrix input sense 2, internal pull up 10k 29 sense3 i key matrix input sense 3, internal pull up 10k 30 sense4 i key matrix input sense 4, internal pull up 10k 31 sense5 i key matrix input sense 5, internal pull up 10k 32 sense6 i key matrix input sense 6, internal pull up 10k 33 sense7 i key matrix input sense 7, internal pull up 10k 34 sense8 i key matrix input sense 8, internal pull up 10k 35 p1.5/numlock i/o port 1 bit 5/number lock indicator, internal pull up 36 p1.6/capslock i/o port 1 bit 6/caps lock indicator, internal pull up 37 p1.7/scrolllock i/o port 1 bit 7/scroll lock indicator, internal pull up 38 vdd - voltage supply 39 xtal1 o ceramic resonator or crystal out 40 xtal2 i ceramic resonator or crystal in note 1: name or description after ?/? means default function specified by genesys logic firmware
revision 1.6 -7- 02/28/2000 figure 3-1 40-pin dip (GL602USB) 3.2 GL602USB-a table 3-2 GL602USB-a pin definitions and descriptions pin no. name i/o description 1 gnd - ground 2 v3.3 o 3.3v output 3 d+ i/o usb data+ 4 d- i/o usb data- 5 p1.1/mouse clk i/o port 1 bit 1/ps2 mouse clock input 6 p1.2/mouse data i/o port 1 bit 2/ps2 mouse data input 7 p1.3/vpp i/o port 1 bit 3 (for mask) / 12.75v programming power (for otp) 8 p1.4/pwrctl i/o port 1 bit 4 / ps2 mouse power control 9 drv7 o key matrix output drive 7, open drain output 10 drv8 o key matrix output drive 8, open drain output 11 drv10 o key matrix output drive 10, open drain output 12 drv12 o key matrix output drive 12, open drain output 13 drv13 o key matrix output drive 13, open drain output 14 drv15 o key matrix output drive 15, open drain output 15 drv16 o key matrix output drive 16, open drain output 16 drv17 o key matrix output drive 17, open drain output 17 sense1 i key matrix input sense 1, internal pull up 10k 18 sense3 i key matrix input sense 3, internal pull up 10k 19 sense6 i key matrix input sense 6, internal pull up 10k 20 sense8 i key matrix input sense 8, internal pull up 10k 21 p1.7/led i/o port 1 bit 7/led indicator 22 vdd - voltage supply 23 xtal1 o ceramic resonator or crystal out 24 xtal2 i ceramic resonator or crystal in 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 xtal2 xtal1 vdd p1.7scrolock p1.6/capslock p1.5/numlock sense8 sense7 sense6 sense5 sense4 sense3 sense2 sense1 drv18 drv17 drv16 drv15 drv14 drv13 gnd v3.3 d+ d- drv1 drv2 p1.1/moust clk p1.2/mouse data p1.3 p1.4/pwrctl drv3 drv4 drv5 drv6 drv7 drv8 drv9 drv10 drv11 drv12
revision 1.6 -8- 02/28/2000 note 1: name or description after ?/? means default function specified by genesys logic firmware figure 3-2 24-pin sop (GL602USB-a) 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 vdd p1.7/led sense8 sense6 sense3 sense1 drv17 drv16 drv15 drv13 gnd v3.3 d+ d- p1.1/mouse clk p1.2/mouse data p1.3/vpp p1.4/pwrctl drv7 drv8 drv10 drv12 xtal1 xtal2
revision 1.6 -9- 02/28/2000 4. functional description the genesys logic GL602USB micro-controller is optimized for pc keyboard. this usb microcontroller conforms to the low-speed (1.5mbps) requirements of the usb specification version 1.1. the micro-controller is a self-contained unit with an usb sie, an usb transceiver, an 8-bit risc-like microcontroller, a timer, data and program memories. it supports one usb device address and four endpoints (include endpoint 0). 4.1 memory organization the memory in the microcontroller is organized into user program memory in program rom and data memory in sram space. 4.1.1 program memory organization the 12-bit program counter (pc) is capable of addressing 4k x 14 of program space. all of the 4k * 14 rom space can be used. the program memory space is divided into two functional groups: interrupt vectors and program code. after a reset, the program counter points to location zero of the program space and all registers are reset to the default value. after a timer interrupt, the program counter points the location 0x0004 of the program space. address after reset 0x0000 reset vector after timer interrupt 0x0004 timer interrupt vector 0x0005 0x0fff 4k x 14 rom figure 4-1 program memory space 4.1.2 data memory organization the data memory is partitioned into two banks that contain the general purpose registers, mcu function registers and usb function registers. bit bs is the bank select bit. bs (status<5>) = 1 bank 1 bs (status<5>) = 0 bank 0 the lower locations of each bank are reserved for mcu function registers and usb function registers. above the mcu function registers and usb function registers are general purpose registers implemented as sram. both bank 0 and bank 1 contain mcu function registers. usb function registers are located in bank 0. some ?high use? mcu function registers from bank 0 are mirrored in bank 1 for code reduction and quicker access. data memory address data memory address 00h indr 80h indr 01h timer 81h pscon 02h pcl 82h pcl 03h status 83h status 04h indar 84h indar 05h 85h 06h port1 86h port1con
revision 1.6 -10- 02/28/2000 07h 87h 08h 88h 09h 89h 0ah pchbuf 8ah pchbuf 0bh inten 8bh inten 0ch 8ch 0dh 8dh 0eh 8eh 0fh 8fh 10h devctl 11h evtflg 12h devadr 13h rxctl0 14h txctl0 15h txctl123 16h ffdat0 17h ffdat123 18h drvsel 19h sense 1ah ffrst 1bh modesel 1ch ps2ctl 1dh epsel 1eh serctl 1fh serdat 20h 7fh general purpose registers (96 bytes) ffh bank 0 bank 1 figure 4-2 data memory space
revision 1.6 -11- 02/28/2000 4.2 usb function registers table 4-1 usb function register summary address name function 10h devctl device control register 11h evtflg event flag register 12h devadr usb device address register 13h rxctl0 endpoint 0 receive control register 14h txctl0 endpoint 0 transmit control register 15h txctl123 endpoint 1/2/3 transmit control register 16h ffdat0 endpoint 0 fifo data port 17h ffdat123 endpoint 1/2/3 fifo data port 18h drvsel key matrix drive pin control register 19h sense key matrix sense register 1ah ffrst fifo reset register 1bh modesel usb mode select register 1ch reserved 1dh epsel endpoint select register 1eh serctl ps/2 mouse port control register 1fh serdat ps/2 mouse port data register devctl (address 10h, device control register) r/w [1] r/w r/w r/w r/w r/w r/w ep3stl ep2stl ep1stl ep0stl wake wkdis pwrdn ep3stl: endpoint 3 stall bit 1: endpoint 3 will respond with a stall to a valid transaction 0: endpoint 3 will not respond with a stall to a valid transaction ep2stl: endpoint 2 stall bit 1: endpoint 2 will respond with a stall to a valid transaction 0: endpoint 2 will not respond with a stall to a valid transaction ep1stl: endpoint 1 stall bit 1: endpoint 1 will respond with a stall to a valid transaction 0: endpoint 1 will not respond with a stall to a valid transaction ep0stl: endpoint 0 stall bit 1: endpoint 0 will respond with a stall to a valid transaction. 0: endpoint 0 will not respond with a stall to a valid transaction wake: wake-up bit 1: set this bit to wake up host controller by placing usb bus into k state 0: clear this bit to force usb bus leave k state wkdis: wake-up disable bit 1: disable remote wake-up capability 0: enable remote wake-up capability pwrdn: power-down mode bit 1: entering power-down mode if usb suspend is detected, firmware should set this bit to enter power-down mode. in power-down mode, 6mhz crystal clock will be stopped. hardware will automatically clear pwrdn bit upon hardware reset, usb d+/d- toggle, sense1~sense8 at logic ?0?, or port 1.1 at logic ?0?. value on por: ?0 0 0 0 0 0 0 0? note 1: ?r/w? means readable and writable bit evtflg (address 11h, event flag register) r/w1c [1] r/w1c r/w1c r/w1c r/w1c r/w1c r/w1c r/w1c wakeup resume suspd ep3tx ep2tx ep1tx ep0tx ep0rx
revision 1.6 -12- 02/28/2000 wakeup: remote wakeup bit 1: remote wakeup from p1.1~p1.4 or sense1~sense8 was detected 0: remote wakeup was not detected resume: global resume bit 1: global resume (usb d+/d- toggle) was detected 0: global resume was not detected suspd: global suspend bit 1: global suspend (usb idle more than 3ms) was detected 0: global suspend was not detected ep3tx: endpoint 3 transmitting status bit 1: data has been sent from endpoint 3 0: data has not been sent from endpoint 3 ep2tx: endpoint 2 transmitting status bit 1: data has been sent from endpoint 2 0: data has not been sent from endpoint 2 ep1tx: endpoint 1 transmitting status bit 1: data has been sent from endpoint 1 0: data has not been sent from endpoint 1 ep0tx: endpoint 0 transmitting status bit 1: data has been sent from endpoint 0 0: data has not been sent from endpoint 0 ep0rx: endpoint 0 receiving status bit 1: data has been received by endpoint 0 0: data has not been received by endpoint 0 value on por: ?0 0 0 0 0 0 0 0? note 1: ?r/w1c? means read-only and write ?1? to clear bit devadr (address 12h, usb device address register) r/w r/w r/w r/w r/w r/w r/w dadr6 dadr5 dadr4 dadr3 dadr2 dadr1 dadr0 write this register to set the usb device address value on por: ?0 0 0 0 0 0 0 0? rxctl0 (address 13h, endpoint 0 receive control register) r/w r/o [1] r/o r/o r/w r/w r/w r/w rxdis rxst2 rxst1 rxst0 rxcnt3 rxcnt2 rxcnt1 rxcnt0 rxdis: endpoint 0 receiving not available bit 1: endpoint 0 fifo is not available. the received data cannot be pushed into fifo. the usb controller will respond with a nak to a valid out transaction. this bit is set by hardware when endpoint 0 data is received (both setup and out transaction). 0: endpoint 0 fifo is available for data receiving rxst[2:0]: rxst[2:0] indicate the pid received. bit value packet received 100 setup token with data0 packet 010 out token with data0 packet 011 out token with data1 packet rxcnt[3:0]: number of bytes received from endpoint 0. value on por: ?0 x x x x x x x? note 1: ?r/o? means read-only bit txctl0 (address 14h, endpoint 0 transmit control register) r/w r/w r/w r/w r/w r/w txseq txoe txcnt3 txcnt2 txcnt1 txcnt0 txseq: endpoint 0 transmitting sequence bit 1: transmitting data use data1 as pid 0: transmitting data use data0 as pid
revision 1.6 -13- 02/28/2000 txoe: endpoint 0 fifo data ready bit 1: endpoint 0 fifo data are ready to be transmitted. data will be transmitted when a valid in token is received. this bit is automatically cleared by hardware after the transaction complete (ack is received). 0: endpoint 0 fifo data are not ready to be transmitted and respond with a nak to a valid in transaction. txcnt[3:0]: number of bytes to be sent by endpoint 0 when in token is received value on por: ?0 0 0 0 0 0 0 0? txctl123(address 15h, endpoint 1/2/3 transmit control register) r/w r/w r/w r/w r/w r/w txseq txoe txcnt3 txcnt2 txcnt1 txcnt0 txseq: endpoint 1/2/3 transmitting sequence bit 1: transmitting data use data1 as pid 0: transmitting data use data0 as pid txoe: endpoint 1/2/3 fifo data ready bit 1: endpoint 1/2/3 fifo data are ready to be transmitted. data will be transmitted when a valid in token is received. this bit is automatically cleared by hardware after the transaction complete (ack is received). 0: endpoint 1/2/3 fifo data are not ready to be transmitted and respond with a nak to a valid in transaction. txcnt[3:0]: number of bytes to be sent by endpoint 0 when in token is received value on por: ?0 0 0 0 0 0 0 0? ffdat0 (address 16h, endpoint 0 fifo port) r/w r/w r/w r/w r/w r/w r/w r/w ffdat7 ffdat6 ffdat5 ffdat4 ffdat3 ffdat2 ffdat1 ffdat0 endpoint 0 fifo data port endpoint 0 fifo is a 8 bytes fifo. firmware can read/write this port 8 times to get/put the fifo data. value on por: ?x x x x x x x x? ffdat1/2/3 (address 17h, endpoint 1/2/3 fifo port) r/w r/w r/w r/w r/w r/w r/w r/w ffdat7 ffdat6 ffdat5 ffdat4 ffdat3 ffdat2 ffdat1 ffdat0 endpoint 1/2/3 fifo data port endpoint 1 fifo is 8 bytes fifo. firmware can read this port 8 times to get the fifo data. endpoint 2 fifo is 6 bytes fifo. firmware can read this port 6 times to get the fifo data. endpoint 3 is 2 bytes fifo only. firmware can read this port 2 times to get the fifo data. before read this register, firmware should selects endpoint via epsel register (address 1dh). value on por: ?x x x x x x x x? drvsel (address 18h, key matrix drive pin control register) r/w r/w r/w r/w r/w r/w r/w invdrv drvoe drv4 drv3 drv2 drv1 drv0 invdrv: inverse drive signal. this function can be used to detected ghost keys. 1: drive all drv1-18 to low except the selected pin when drvoe is set 0: drive the selected pin to low only when drvoe is set drvoe: drv1-18 output enable 1: enable drv1-18 pins to drive key matrix 0: disable drv1-18 pins and not to drive key matrix drv[4:0]: select drv1 to drv18 port to drive low if drvoe is set. 5?h00 selects drv1 5?h01 selects drv2 5?h0f selects drv16 5?h10 selects drv17 5?h11 selects drv18 5?h12 ~ 5?h1f are invalid. value on por: ?0 0 0 0 0 0 0 0? sense (address 19h, key matrix sense resister)
revision 1.6 -14- 02/28/2000 r/o r/o r/o r/o r/o r/o r/o r/o sense8 sense7 sense6 sense5 sense4 sense3 sense2 sense1 key matrix sense input port all sense1~sense8 bits indicate state of the corresponding sense1~sense8 pins. value on por: ?x x x x x x x x? ffrst (address 1ah, fifo reset register) w/o w/o ffrst123 ffrst0 ffrst123: reset endpoint 1/2/3 fifo read/write pointer write ?1? to this bit will reset endpoint 1/2/3 fifo read/write pointer. data in endpoint 1/2/3 fifo remain unchanged. before data are written into endpoint 1/2/3 fifo, epsel should be set correctly then ffrst123 should be set. ffrst0: reset endpoint 0 fifo read/write pointer write ?1? to this bit will reset endpoint 0 fifo read/write pointer. data in endpoint 0 fifo remain unchanged. before data are read/written into endpoint 0 fifo, ffrst0 should be set first. modesel (address 1bh, mode select register) r/w r/w oscstp pwron oscstp: suspend clock stop control bit 1: clock is stopped while suspend 0: clock is not stopped while suspend pwron: power reset indicator 1: power on reset detected 0: usb bus reset detected value on por: ?- - - - - - 0 1? usbioctl (address 1ch, i/o control register for usb d+/d-) r/w r/w r/w r/w dmoe dpoe dm dp dmoe: d- pin output enable control bit 1: d- pin digital output enable 0: d- pin digital output disable dpoe: d+ pin output enable control bit 1: d+ pin digital output enable 0: d+ pin digital output disable dm: digital output value of d- pin. this pin is open drain output. output high will be tri-stated. dp: digital output value of d+ pin. this pin is open drain output. output high will be tri-stated. value on por: ?- - - - 1 1 0 0? epsel (address 1dh, endpoint select register) r/w r/w r/w epsel3 epsel2 epsel1 epsel[3: 1]: endpoint select control bits bit value endpoint to be selected 001 endpoint 1 010 endpoint 2 100 endpoint 3 value on por: ?- - - - - x x x? serctl (address 1eh, ps/2 or rs232 mouse port control register) r/wc r/w rxflg srxen rxflg: data received flag on ps/2 interface 1: data received and saved in serbuf
revision 1.6 -15- 02/28/2000 0: no data received srxen: receiver enable bit for ps/2 interface 1: enable serial port receiver 0: disable serial port receiver value on por: ?- - - - - 0 - 0? serdat (address 1fh, ps/2 mouse port data register) r/w r/w r/w r/w r/w r/w r/w r/w serdat7 serdat6 serdat5 serdat4 serdat3 serdat2 serdat1 serdat0 serdat[7: 0]: ps/2 mouse data input port. this port is a 2 bytes fifo. therefore, about 1 mini-second delay is allowed between rxflg in serctl register set and to read the ps/2 mouse data. if the 2 bytes fifo full, GL602USB will drive the ps/2 clock low to avoid the mouse send more data. value on por: ?x x x x x x x x?
revision 1.6 -16- 02/28/2000 4.3 mcu function registers table 4-2 mcu function register summary address name function 00h indr addressing this location will use the content of indar to address data memory (not a physical address) 01h timer timer register 02h pcl program counter?s low byte 03h status status register 04h indar indirect address register 05h reserved 06h port1 port 1 data register 0ah pchbuf write buffer of program counter?s bit 11-8 0bh inten interrupt enable register 80h indr addressing this location will use the content of indar to address data memory (not a physical address) 81h pscon prescaler control register 82h pcl program counter?s low byte 83h status status register 84h indar indirect address register 85h reserved 86h port1con port 1 direction control register 8ah pchbuf write buffer of program counter?s bit 12-8 8bh inten interrupt enable register indr (address 00h/80h) indr is not a physical register. addressing indr register will cause indirect addressing. any instruction using the indf register actually accesses the register pointed by the indar register. the indirect addressing method only can be used for general purpose registers. timer (address 01h, timer register) r/w r/w r/w r/w r/w r/w r/w r/w timer7 timer6 timer5 timer4 timer3 timer2 timer1 timer0 the timer starts to count up after power on reset. the tmrof bit at inten register will be set when the timer register overflows from ffh to 00h. if both tmroen and gie bits at inten register are set, an interrupt will be generated when timer register overflows. value on por: ?0 0 0 0 0 0 0 0? pcl (address 02h/82h, program counter?s low byte) r/w r/w r/w r/w r/w r/w r/w r/w pcl7 pcl6 pcl5 pcl4 pcl3 pcl2 pcl1 pcl0 the program counter (pc) is 12-bits wide. the low byte comes from the pcl register, which is a readable and writable register. the high byte is not directly readable or writable and comes from pchbuf. the GL602USB has a 8 level deep x 11-bit wide hardware stake. the stake space is not part of either program or data space and the stack pointer is not readable or writable. the pc is pushed onto the stack when a call instruction is executed or an interrupt causes a branch. the stack is poped in the event of a retia, reti or a ret instruction execution. pchbuf is not affected by a push or pop operation. because branch address gotten from stack or direct from instruction is only 11 bits long, the highest bit will be loaded to pc from pchbuf when branch instruction is executed. when write to pcl command executed, all 4 bits of pchbuf will be loaded to pc because pcl is only a 8 bits register. value on por: ?0 0 0 0 0 0 0 0?
revision 1.6 -17- 02/28/2000 status (address 03h, status register) r/w r/w r/w r/w bs zo hc ca bs: bank select. because only 7 bits (bit 0~bit 6) operand implied by instruction for register address, this bit is used as address bit 7 when register access. 1: bank 1 (80h-ffh) 0: bank 0 (00h-7fh) zo: zero bit 1: the result of last arithmetic or logic operation is zero 0: the result of last arithmetic or logic operation is not zero hc: half carry/borrow bit 1: carry or not borrow from the 4 th low order bit 0: borrow or not carry from the 4 th low order bit ca: carry/borrow bit 1: carry or not borrow from the most significant bit 0: borrow or not carry from the most significant bit value on por: ?- - 0 - - 0 0 0? indar: (address 04h/84h, indirect address register) r/w r/w r/w r/w r/w r/w r/w r/w indar7 indar6 indar5 indar4 indar3 indar2 indar1 indar0 any instruction using the indf register actually accesses the register pointed by the indar register. value on por: ?x x x x x x x x? [1] note 1: ?x? means unknown port1 (address 06h, port 1 data register) r/w r/w r/w r/w r/w r/w r/w port 1.7 port1.6 port1.5 port1.4 port1.3 port1.2 port1.1 port1 is a 7-bits latch for port 1.1~port 1.7. reading the port1 register gets the status on the pins. writing to it will write to the port latch. all write operations are read-modify-write operations. port1con is used to enable/disable every bits of the port latch. value on por: ?x x x x x x x -? pchbuf (address 0ah/8ah, write buffer of program counter?s bit 11-8) r/w r/w r/w r/w pchbuf3 pchbuf2 pchbuf1 pchbuf0 write buffer for upper 4-bits of program counter. the upper byte of program counter is not directly accessible. pchbuf is a holding register for the pc[11:8] that are transferred to the upper byte of the program counter when branch occur. please see pcl register to get more detail information. value on por: ?- - - 0 0 0 0 0? inten (address 0bh/8bh, interrupt enable register) r/w r/w r/w gie tmroen tmrof gie: global interrupt enable bit 1: enable all interrupts 0: disable all interrupts tmroen: timer overflow interrupt enable bit 1: enable timer interrupt 0: disable timer interrupt tmrof: timer overflow interrupt flag bit. this bit should be cleared to ?0? by firmware after it is set by hardware. 1: timer register has overflowed 0: timer register did not overflow value on por: ?0 - 0 - - 0 - -? pscon (address 81h, prescaler control register)
revision 1.6 -18- 02/28/2000 r/w r/w r/w r/w psdis ps2 ps1 ps0 psdis: prescaler disable bit 1: set prescaler disable 0: set prescaler enable ps[2:0]: prescaler rate select bits. these bits are used to control timer speed. the following table means that how many instruction cycles the timer register should be added by 1 when psdis = 0. bit value timer rate (psdis = 0) 000 1:2 001 1:4 010 1:8 011 1:16 100 1:32 101 1:64 110 1:128 111 1:256 value on por: ?- - - - 1 1 1 1? port1con (address 86h, port 1 direction control register) r/w r/w r/w r/w r/w r/w r/w p1con7 p1con6 p1con5 p1con4 p1con3 p1con2 p1con1 there is a data direction control bit to match every pin of port 1. the direction control bits can configure these pins as output or input. setting a port1con register bit put the corresponding output driver in a hi-impedance mode. clearing a bit in the port1con register puts the contents of the output latch on the selected pin. value on por: ?1 1 1 1 1 1 1 -? 4.4 general purpose i/o ports interface with peripherals is conducted via up to 7 gpio signals. the 7 signals are located at port 1. the port 1 data register is located at data memory address 06h and direction control register is located at address 86h. the GL602USB builds in a ps/2 host data receiver. while this receiver enabled, the port 1.1 is treated as ps/2 clk and port 1.2 is treated as ps/2 data. firmware uses these 2 pins to implement a ps/2 mouse host controller. when the ps/2 host want to send command to ps/2 device, firmware should drive the 2 i/o pins directly following ps/2 specification. there are 2 bytes fifo used as ps/2 data buffer. when the ps/2 receiver has received a data byte already and firmware does not read it yet, the ps/2 receiver can receive the next data byte into fifo still. if the firmware cannot process the first byte until the second byte received complete, the ps/2 receiver will drive low on port 1.1 (ps/2 clk) automatically to avoid the ps/2 device send data again. p1.3 is vpp pin at otp. this i/o pin can be used only at mask type. the port 1.5/port 1.6/port 1.7 can be treat as general purpose output pins in output mode. there are internal pull up resistors on those pins. firmware can drive high on these pins to turn off leds and drive low to turn off these pins. external resistors are needed for these led pins to sink current . 4.5 timer interrupt the timer interrupt is generated when the timer register overflows from ffh to 00h. this overflow sets bit tmrof (inten<2>). the interrupt can be masked by clearing bit tmroen (inten<5>). bit tmrof must be cleared in software by the timer module interrupt service routine otherwise the timer interrupt will not be generated again. if prescaler is disabled, the timer register will increase every instruction cycle. if prescaler is enabled, its increment cycle depends on ps0~ps2 bits in pscon register.
revision 1.6 -19- 02/28/2000 4.6 usb engine the usb module contains three functional blocks: a 3.3-volt regulator, a low-speed usb transceiver, and the serial interface engine (sie). the usb module is only enabled under usb mode. the following description is the function of the regulator, transceiver, and sie. 4.6.1 voltage regulator the usb data lines are required by the usb specification to have a maximum output voltage between 2.8v and 3.6v. because the GL602USB is a low speed usb device, the d- lines also are required to have an external 1.5-k ? pull-up resistor connected between a data line and a voltage source between 3.0 v and 3.6 v. since the power provided by the usb cable is specified to be between 4.4v and 5.0v, an on-chip regulator is used to drop the voltage to the appropriate level for sourcing the usb transceiver and external pull-up resistor. an output pin driven by the regulator is provided to source the 1.5-k ? external resistor. 4.6.2 usb transceiver the usb transceiver provides the physical interface to the usb d+ and d- data lines. the transceiver is composed of two parts: an output driver circuit and a receiver. the usb transceiver uses a differential output driver to drive the usb data signal onto the usb cable. the static output swing of the driver in its low state is below the v ol of 0.3v with 1.5-k ? load to 3.6v and in its high state is above the v oh of 2.8v with 15-k ? load to ground. the output swings between the differential high and low state are well balanced to minimize signal skew. slew rate control on the driver is used to minimize the radiated noise and cross talk. the driver?s outputs support 3-state operation to achieve bi-directional half-duplex operation. the driver can tolerate a voltage on the signal pins of ?0.5v to 3.8v with respect to local ground reference without damage. the rise and fall time of the signals on this cable are greater than 75ns to keep rfi (radio frequency interference) emissions under fcc (federal communications commission) class b limits and less than 300ns to limit timing delays, signaling skews, and distortions. the driver reaches the specified static signal levels with smooth rise and fall times, and minimal reflections and ringing when driving the cable. this driver is used only on segments between low-speed devices and the ports to which they are connected. usb data transmission is done with differential signals. a differential input receiver is used to accept the usb data signal. a differential 1 on the bus is represented by d+ being at least 200mv more positive than d- as seen at the receiver, and a differential 0 is represented by d- being at least 200mv more positive than d+ as seen at the receiver. the signal cross over point must be between 1.3v and 2.0v. the receiver features an input sensitivity of 200mv when both differential data inputs are in the range of 0.8v and 2.5v with respect to the local ground reference. this is called the common mode input voltage range. proper data reception also is achieved when the differential data lines are outside the common mode range. the receiver can tolerate static input voltage between ?0.5v to 3.8v with respect to its local ground reference without damage. in addition to the differential receiver, there is a single-ended receiver for each of the two data lines.
revision 1.6 -20- 02/28/2000 0.0 0.2 0.4 0.6 0.8 1.0 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 common mode input voltage (volts) minimum differential sensitivity (volts) figure 4-3 differential input sensitivity over entire common mode range the data receivers for all types of devices must be able to properly decode the differential data in the presence of jitter. the more of the bit time that any data edge can occupy and still be decoded, the more reliable the data transfer will be. data receivers are required to decode differential data transitions that occur in a window plus and minus a nominal quarter bit time from the nominal (centered) data edge position. jitter will be caused by the delay mismatches and by mismatches in the source and destination data rates (frequencies). d d i i f f f f e e r r e e n n t t i i a a l l d d a a t t a a l l i i n n e e s s p p a a i i r r e e d d t t r r a a n n s s i i t t i i o o n n s s n n * * t t p p e e r r i i o o d d + + t t j j r r 2 2 t t p p e e r r i i o o d d c c o o n n s s e e c c u u t t i i v v e e t t r r a a n n s s i i t t i i o o n n s s n n * * t t p p e e r r i i o o d d + + t t j j r r 1 1 t t j j r r t t j j r r 1 1 t t j j r r 2 2 figure 4-4 receiver jitter tolerance the source of data can have some variation (jitter) in the timing of edges of the data transmitted. the time between any set of data transitions is n*t period jitter time, where n is the number of bits between the transitions and t period is defined as the actual period of the data rate. the data jitter is measured with the same capacitive load used for maximum rise and fall times and is measured at the crossover points of the data lines. for low-speed transmissions, the jitter time for any consecutive differential data transitions must be within 25ns and within 10ns for any set of paired differential data transitions. these jitter numbers include timing variations due to differential buffer delay, rise/fall time mismatches, internal clock source jitter, noise and other random effects. the output rise time and fall time are measured between 10% and 90% of the signal. edge transition time for the rising and falling edges of low-speed signals is 75ns (minimum) into a capacitive load (c l ) of 50pf and 300ns (maximum) into a capacitive load of 350pf. the rising and falling edges should be transitioning (monotonic) smoothly when driving the cable to avoid excessive emi.
revision 1.6 -21- 02/28/2000 low speed: 75ns at c l = 50pf, 300ns at c l = 350pf full speed: 4 to 20ns at c l = 50pf differential data lines 10 % rise time 90 % fall time t f t r 10 % 90 % c l c l figure 4-5 data signal rise and fall time 4.6.3 serial interface engine (sie) the sie manages data movement between the cpu and the transceiver. the sie handles both transmit and receive operations on the usb. it contains the logic used to manipulate the transceiver and the endpoint registers. the byte count buffer is loaded from txcnt(txctl0<3~0>) during endpoint 0 transmit operations. this same buffer is used for receive transactions to count the number of bytes received at endpoint 0 and, upon the end of transaction, transfer the value to rxcnt(rxctl0<3~0>). when transmitting, the sie handles parallel-to-serial conversion, crc generation, nrzi encoding, and bit stuffing. when receiving, the sie handles sync detection, packet identification, end-of-packet detection, bit (un)stuffing, nrzi decoding, crc validation, and serial-to-parallel conversion. errors detected by the sie include bad crc, timeout while waiting for eop, and bit stuffing violations. all usb devices are required to have an endpoint 0 that is used to initialize and manipulate the device. endpoint 0 provides access to the device?s configuration information and allows generic usb status and control accesses. endpoint 0 can receive and transmit data. both receive and transmit data share the same 8- byte endpoint 0 fifo, ffdat0. received data may overwrite the data previously in the fifo. transmission from endpoint 0 is controlled by txctl0 and receiving from endpoint 0 is controlled by rxctl0. endpoint 1/endpoint 2/endpoint 3 are of transmit only. transmission from endpoint 1/endpoint 2/endpoint 3 is controlled by txctl123. the target endpoint should be chosen before writing to ffdat123 and txctl123. there are separated fifo buffer for the 3 endpoints, but the programming interface for them is unique, via ffdat123 register. size of endpoint 1 fifo is 8 bytes, endpoint 2 fifo is 6 bytes, and endpoint 3 fifo is 2 bytes. 4.7 instruction set summary 4.7.1 operand field descriptions field description r register address a accumulator i immediate data b bit address within a 8-bit register 4.7.2 instruction set mnemonic, operands description cycles flags affected arithmetic operations
revision 1.6 -22- 02/28/2000 addar r, a add r and a, r <- r + a 1 ca, hc, zo addar a, r add a and r, a <- a + r 1 ca, hc, zo addai i add a and i, a <- a + i 1 ca, hc, zo incr r increment r, r <- r +1 1 zo incr a, r increment r, a <- r + 1 1 zo incrsz r increment r, r <- r +1, skip if (r = 0) 1 or 2 incrsz a, r increment r, a <- r +1, skip if (a = 0) 1 or 2 subar r, a subtract a from r, r <- r - a 1 ca, hc, zo subar a, r subtract a from r, a <- r - a 1 ca, hc, zo subia i subtract a from i, a <- i - a 1 ca, hc, zo decr r decrement r, r <- r -1 1 zo decr a, r decrement r, a <- r -1 1 zo decrsz r decrement r, r <- r-1, skip if (r = 0) 1 or 2 decrsz a, r decrement r, a <- r -1, skip if (a = 0) 1 or 2 clrr r clear r, r <- 0 1 zo clra clear a, a <- 0 1 zo nop no operation 1 logical operations andar r, a and r and a, r <- r & a 1 zo andar a, r and a and r, a <- a & r 1 zo andai i and a and i, a <- a & i 1 zo cmpr r complement r, r <- r ^ ff 1 zo cmpr a, r complement r, a <- r ^ ff 1 zo orar r, a inclusive or r with a, r <- r | a 1 zo orar a, r inclusive or a with r, a <- a | r 1 zo oria i inclusive or i with a, a <- a | i 1 zo xorar r, a exclusive or r with a, r <- r ^ a 1 zo xorar a, r exclusive or a with r, a <- a ^ r 1 zo xoria i exclusive or i with a, a <- a ^ i 1 zo bit-wise operations bcr r, b bit clear r, r.b <- 0 1 bsr r, b bit set r, r.b <- 1 1 btrsc r, b bit test r, skip if (r.b = 0) 1 or 2 btrss r, b bit test r, skip if (r.b =1) 1 or 2 data movement operations mov r, a move a into r, r <- a 1 mov a, r move r into a, a <- r 1 zo movia i move i into a, a <- i 1 shift operations swapr r swap high and low nibbles in r, result put into r 1 swapr a, r swap high and low nibbles in r, result put into a 1 rlr r rotate r left through c, (c, r) <- (r, c) 1 ca rlr a, r rotate r left through c, (c, a) <- (r, c) 1 ca rrr r rotate r right through c, (r, c) <- (c, r) 1 ca rrr a, r rotate r right through c, (a, c) <- (c, r) 1 ca control transfer operations call i call subroutine 2 jump i jump to address 2 retia return and load i to a 2 reti return from timer interrupt 2 ret return from subroutine 2
revision 1.6 -23- 02/28/2000 5. firmware programming guide 5.1 usb power on reset and bus reset initialization power on reset usb reset (address 0) pwron = 1 no usb reset detected wait host controller to initialize the usb device yes drive (0, 0) on (dp, dm) about 200 ms set dp, dm to input mode set pwron = 0 wait for usb reset
revision 1.6 -24- 02/28/2000 5.2 suspend/resume/wakeup suspd = 1 disable external ps/2 mouse power if needed set pwrdn bit to enter power down mode w ait for resum e or w akeup enable external ps/2 mouse power if needed resume = 1 w rite '1' to clear suspd w rite '1' to clear resume w rite '1 ' to c le a r wakeup suspend & wakeup process com plete keyboard is really pressed ? yes no no set wake bit to drive 'k ' s ta te o n u s b yes delay about 1 ms to clear wake bit
revision 1.6 -25- 02/28/2000 5.3 receive packet via endpoint 0 ep0rx = 1 packet received com plete w rite '1 ' to c le a r ep0rx bit get received byte count from rxcnt read received data continuous from ffdat0 (total rxcnt bytes) clear rxdis bit to enable endpoint 0 receiver r x s t = (1, 0, 0) setup data packet received com plete out data packet received com plete no yes
revision 1.6 -26- 02/28/2000 5.4 transmit packet via endpoint 0 s ta rt to tran sm it fu nctio n set ffrst0 to reset fifo push all transm itting data into ffdat0 (m axim um 8 bytes) s e t c orrect da ta togg le sequence via t xseq and s e t tran sm it d ata le n g th in to t x c n t s et t x o e bit s ie w ill trans m it the packet while it rece ive s a in toke n
revision 1.6 -27- 02/28/2000 5.5 transmit packet via endpoint 1/2/3 s ta rt to tra n sm it fu n ctio n set ffrst123 to reset fifo push all transm itting data into ffdat123 (m axim um 8 bytes) s e t c o rre ct d a ta to g g le sequence via t xseq and s e t tra n sm it d a ta le n g th in to t x c n t s e t t x o e b it s ie w ill tra n s m it the packet while it re ce ive s a in to ke n s e le ct ta rg e t endpoint via epsel
revision 1.6 -28- 02/28/2000 5.6 timer interrupt because cpu may enter timer interrupt routine at any time, the timer interrupt routine should backup all special registers at its entry point and restore them before return. (address 0x004) timer_entry: mov a_temp, a swapr a, status bcr status, bs mov s_temp, a mov a, indar mov i_temp, a ; ; execute interrupt service routine ; mov a, i_temp mov indar, a swapr a, s_temp mov status, a swapr a_temp swapr a, a_temp bcr inten, tmrof reti 5.7 conditional branch example: conditional branch can be according to value of accumulator. firmware can use this method to return value for lookahead table. because accumulator is only 8 bits wide, the higher 5 bits of program counter should be load into pchbuf before the conditional branch executed. (address 0x540) lookahead: movia 0x05 mov pchbuf, a movia lookahead_val addar pcl, a retia 0 ; acc = 0 retia 1 ; acc = 1 retia 2 ; acc = 2 . . . . . . 5.8 change register bank usually keeps bs = 0. if firmware want to access register address 0x80 to 0x8f, set bs = 1. after process register address 0x80 to 0x8f complete, clear bs = 0 to address 0x00 to 0x7f. bsr status, bs mov port1con, a bcr status, bs 5.9 change code bank because pcl is only 11 bits wide, program counter can only jump in 2k boundary directly. if program counter want to jump over 2k boundary, firmware should set pchbuf to correct bank first.
revision 1.6 -29- 02/28/2000 (address 0x375) movia 0x08 mov pchbuf, a jump dest_addr (address 0x83a) dest_addr: 5.10 receive data from ps/2 mouse port check ps/2 m ouse data receiver w rite '1' to clear rxflg rxflg = 1 read a new ps/2 data byte from serdat process received ps/2 mouse data r eturn to m ain program yes no
revision 1.6 -30- 02/28/2000 5.11 scan key matrix 5.12 turn led on/off to turn leds on, the firmware should set corresponding i/o pins (port 1.5~port 1.7) to output low. an external resistor should be added on every led pins to limit sink current. to turn leds off, the firmware should output high to corresponding i/o pins (port 1.5~port 1.7). scan key matrix select from drv1 to drv18 (write drv[0..4] in drvsel) set drvoe to drive selected drv pin to low read sense register if any bit is logic '0', indicate that the specific key is pressed select next drv pin no all drv pins have been scanned ? scan key matrix complete yes 2 or m ore bits are logic '0' in sense register ? no clear drvoe to float all drv pins set drvoe and invdrv to enable all other drv pins yes any same sense bit is logic '0' at other drv pin ? ghost key detected scanned m atrix invalid. yes no
revision 1.6 -31- 02/28/2000 6. absolute maximum ratings maximum ratings are the extreme limits to which the micro-controller can be exposed without permanently damaging it. the micro-controller contains circuitry to protect the inputs against damage from high static voltages; however, do not apply voltages higher than those shown in the table. keep v in and v out within the range gnd (v in or v out ) v cc . connect unused inputs to the appropriate voltage level, either gnd or v dd . symbol characteristic value unit t stg storage temperature -55 to +150 c t op operating temperature 0 to +70 c v cc supply voltage -0.5 to +7.0 v v in dc input voltage -0.5 to +v cc + 0.5 v i maximum current per pin excluding v dd and v ss 25 ma i mgnd maximum current out of gnd 100 ma i mvcc maximum current out of v cc 100 ma v esd static discharge voltage >4000 v 7. electrical characteristics f osc = 6mhz; operating temperature = 0 to 85 c; v cc = 4.4 to 5.5v symbol characteristic min max units conditions general i cc operating supply current 10 ma i sb supply current ? suspend mode 360 a see note 1 usb interface v oh static output high 2.8 3.6 v r l of 15k ? to gnd v ol static output low 0.3 v r l of 1.5k ? to v3.3 v di differential input sensitivity 0.2 v |(d+) ? (d-)| v cm differential common mode range 0.8 2.5 v include v di range v se single ended receiver threshold 0.8 2.0 v i lo hi-z state data line leakage -10 +10 v 0v < v in < 3.3v v3.3 regulator supply voltage 3.0 3.6 v i l = 4ma gpio interface v oh1 static output high for port1.1-4 2.4 v v cc = 5v; i oh = 4ma v ol1 static output low for port1.1-4 0.4 v v cc = 5v; i ol = 4ma v oh2 static output high for port1.5-7 2.4 v v cc = 5v; i oh = 20ma v ol2 static output low for port1.5-7 0.4 v v cc = 5v; i ol = 20ma v ih static input high 2.0 v v cc = 5v v il static input low 0.9 v v cc = 5v i sink1 sink current for port1.1- 4 4 ma v out = 0.4v; i sink2 sink current for port1.5- 7 20 ma v out = 0.4v; i in input leakage current -1 +1 a v out = 0v or v cc usb low-speed source f op internal o p eratin g 1.5 1.5 mhz
revision 1.6 -32- 02/28/2000 frequency transition time t r rise time 75 ns c l = 50pf 300 ns c l = 350pf t f fall time 75 ns c l = 50pf 300 ns c l = 350pf t rfm rise/fall time matching 80 120 % t r / t f v crs output signal crossover voltage 1.3 2.0 v t drate low speed data rate 1.4775 676.8 1.5225 666.0 mbs ns 1.5mbs 1.5% source differential driver jitter t udj1 to next transition -25 25 ns t udj2 for paired transition -10 10 ns c l = 350pf measured at crossover point receiver data jitter tolerance t djr1 to next transition -75 75 ns t djr2 for paired transition -45 45 ns c l = 350pf measured at crossover point t eopt source eop width 1.25 1.50 s measured at crossover point t deop differential to eop transition skew -40 100 ns measured at crossover point receiver eop width t eopr1 must reject as eop 330 ns t eopr2 must accept 675 ns measured at crossover point notes: 1. i sb measured with usb in suspend mode; using external square wave clock source (f osc = 6mhz); transceiver pull- up resistor of 1.5k ? between v3.3 and d- and 15k ? termination resistors on d+ and d- pins; no port pins sourcing current. the i sb value is including power consumed by external resistors.
revision 1.6 -33- 02/28/2000 8. package diagrams 8.1 40-pin p-dip dimension in mil dimension in mm symbol min nom max min nom max a -- 160 -- -- 4.064 -- a1 74 75 76 1.880 1.905 1.930 b -- 18 -- -- 0.457 -- b1 -- 50 -- -- 1.270 -- c -- 10 -- -- 0.254 -- d 2040 2050 2060 51.816 52.07 52.324 e1 549 550 551 13.945 13.970 13.995 f 590 600 610 14.986 15.240 15.494 e -- 100 -- -- 2.540 -- eb 640 650 660 16.256 16.510 16.764 0 7.5 15 0 7.5 15 figure 7-3 package outline dimension for 40-pin p-dip e1 f eb c b1 b e a a1 d
revision 1.6 -34- 02/28/2000 8.2 24-pin sop d a1 e a b c eb e1 l f eb c
revision 1.6 -35- 02/28/2000 dimension in mils dimension in mm symbol min nom max min nom max a 98 100 102 2.489 2.540 2.591 a1 6 --- --- 0.152 --- --- a2 39 41 43 0.991 1.041 1.092 b --- 16 --- --- 0.406 --- c --- 10 --- --- 0.254 --- d 598 600 602 15.189 15.240 15.291 e1 298 300 302 7.569 7.620 7.671 e --- 50 --- --- 1.270 --- eb 406 410 414 10.312 10.414 10.516 l 30 32 34 0.762 0.813 0.864 --- 5 --- --- 5 --- figure 7-4 package outline dimension for 24-pin sop

▲Up To Search▲

Price & Availability of GL602USB

	To Download GL602USB Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .